In ordinary TCP communication, packets are in the half-open state only briefly as a connection is being initiated; the state changes to active when packets are being exchanged, or closed when the exchange is complete. • time that you specify. You can enable or disable use of the black list using the settings described above. To view the list of currently blacklisted computers, click the Black List button at the bottom of the Firewall Configuration page.

1. Huawei Wifi Modem
2. Huawei Drivers Download

• Connect If it is selected, MT800 will automatically enable the PPP dial connection each time the device is powered on. Auto Connect If it is selected, MT800 will automatically redial after timing out and the disconnection is executed. Manual If it is selected, you need to establish the PPP dial connection manually by clicking on Connect button. • Configuration page Figure 4-10 ADSL mode configuration Save Click the Submit button to save the settings in the RAM.

• 2.3 Powering On MT800 Use the provided power adapter and plug it into a suitable power source nearby. You should see the Power LED indicator light up, which indicates the device is powered on. After a few seconds, look at the LAN LINK indicator and make sure it with steady light, which indicates a valid connection between the router and your computer. • Chapter 3 Before Configuring MT800 To configure MT800, you have to connect MT800 to a computer as shown below. Use the provided straight-through cable.

Is it by way of CAT5 or CAT6 Ethernet? Or are you connecting via USB? Given this is an external DSL modem, you really don't need to install drivers for it. Most external DSL modems are stand alone units these days (unlike regular dial-up modems which required a serial port). XP drivers are generally NOT recommended unless there's no other option.

Downloads PHONES MORE PRODUCTS. ABOUT HUAWEI. About Us; HUAWEI Enterprise; HUAWEI Carrier; HUAWEI Group; HUAWEI Marine; Join Us. User Manuals and How to Factory Reset your Huawei SmartAX MT880 router. Stock firmwares for the SmartAX MT880 are available under the download section on the modem.

PPPoA/PPPoE Select “PPPoE”. User name and The values shall be provided by your ISP. Password Default Route Select “Enable”. • 5.3 PPPoA Configuration Configurations on MT800 Location Parameters Comments Select any one from the eight PVCs. VPI/VCI The value shall be provided by your ISP.

• 4.20 Firmware Upgrade.77 4.21 Alarm. 78 Chapter 5 Service Configuration.

You define NAT rules that specify exactly how and when to translate between public and private IP addresses. Click the NAT of Other Setting in the Wizard Column to set the NAT. • Figure 4-18 Add NAPT rule Figure 4-19 Add DMZ rule. • Figure 4-20 Add REDIRECT rule Parameter explanation The explanation of parameters in the above windows is as below. NAT Configuration: Rule ID: The Rule ID determines the order in which rules are invoked (the lowest numbered rule is invoked first, and so on).

Any custom settings will be lost. 4.20 Firmware Upgrade Click the hyperlink Firmware Upgrade in the Wizard column to open the Firmware Upgrade page and update the system software. • Caution: Do not power off the MT800 during the firmware upgrade process. Otherwise, the configuration in the flash could be damaged. 4.21 Alarm Figure 4-44 Alarm You can view the logs of alarm in response to system events.

Huawei SmartAX MT882 ADSL modem I tried installing the Huawei SmartAX MT882 adsl modem on Windows 7, with the drivers that i used to install on Windows XP. Huawei Smartax Mt882a Manual Win Xp SmartAX MT882 Free Driver Download for Windows Vista, 2003, XP, 2000, NT4, ME, Huawei Technologies Proprietary About.

Wfnse care Alcatel draga? Nici nu mai exista firma Alcatel, acum se numesc Alcatel- Lucent (ALU). Modemurile sunt produse de Thomson (adevarat tot francezi) si atat, nimic mai mult.

Figure 4-5 RFC2684 Bridged Connection-application of DHCP Default Route: This setting specified the IP address below is used for default route of LAN. • through WAN interface whenever a client LAN computer accesses the Internet. Gateway IP address: Enter the Gateway address provided by ISP. Traffic Index: Select the index number for ATM traffic from the pull-down menu. Configured MTU: Enter the maximum bytes of the packet being transmitted during connection. • 4.3.2 RFC2684 Route (IPoA) Configuration Configuration page Figure 4-6 RFC2684 route (IPoA) configuration Parameters explanation PVC: The system provides 8 PVCs.

Select Basic > DHCP in the navigation tree to display the DHCP configuration page. Select DHCP Server in the DHCP configuration page. Click Submit. Select Tools > Save & Reboot in the navigation tree. Select Save in the Save/Reboot page.

After a confirmation page displays, the IP Filter -Configuration page will redisplay with the new rule showing in the table. • No QoS Figure 4-26 QoS-No QoS Application Some special application, such network game, videoconference, network phone, will transmit the audio, video and data synchronously. So you can set the priority level to the different type of traffic. So the traffic with higher priority will be processed firstly while the network jammed. • Priority Queue Index: Provided 4 priority queues. MT800 will set the received traffic into one of 4 priority queues for output. The packet with highest priority will be outputted firstly.

• Chapter 1 Introduction This chapter introduces functions and structure of the SmartAX MT880 ADSL terminal (hereinafter referred to as the MT880). 1.1 Functions and Features The MT880 is a kind of Asymmetric Digital Subscriber Line (ADSL) terminal.

• Select Connect to the Internet and click Next. Select Set up my connection manually and click Next. Select Connect using a broadband connection that requires a username and password and click Next. Enter the name of the connection you are creating. Then click Next. • Name Configuration Username and password for the Provided by the ISP PPPoE dial-up DHCP mode of the MT880 Enable the DHCP server Note: After the DHCP server is enabled, the MT880 can allocate the private IP address for the computer. 3.4.2 Steps 1.

Action(s): Click icon to delete an existed ATM from table; Click icon to view the parameters of an existed DHCP server. • Configuration page Figure 4-22 RIP configuration Change RIP configuration: If necessary, change the Age and Update Time. These are global settings for all interfaces that use RIP. Age is the amount of time in seconds that the device's RIP table will retain each route that it learns from adjacent computers.

This tool will download and update the correct Huawei MT800 driver versions automatically, protecting you against installing the wrong MT800 drivers. Solvusoft: Microsoft Gold Certified Company Recognized for best-in-class capabilities as an ISV (Independent Software Vendor) Solvusoft is recognized by Microsoft as a leading Independent Software Vendor, achieving the highest level of completence and excellence in software development. Solvusoft's close relationship with Microsoft as a Gold Certified Partner enables us to provide best-in-class software solutions that are optimized for performance on Windows operating systems.

Administration Building, Huawei Technologies Co., Ltd., Bantian, Longgang District, Shenzhen, P. China Postal Code: 518129 Website: http://www.huawei.com.

• If the LAN indicator is off, perform further checks as follows: 1. Ensure that the network adapter of the computer is enabled. Ensure that the network cable between the terminal and the computer is properly connected. Remove and then insert the network cable or replace the network cable. If the LAN indicator is still off, contact an authorized maintenance center. • Settings dialog box, ensure that Use a proxy server for your LAN (These settings will not apply to dial-up or VPN connections).

As a Gold Certified Independent Software Vendor (ISV), Solvusoft is able to provide the highest level of customer satisfaction through delivering top-level software and service solutions, which have been subject to a rigourous and continually-audited approval process by Microsoft.

(1)Computer (2)RJ-45 Ethernet Cable (3)MT800 Figure 3-1 Computer to MT800 connection 3.2 When to Configure the MT800 The factory default settings of MT800 have optimized all functions, which made it can operate in most conditions of network. • If the conditions of network have been changed by the modification of security, scale, line of communication, protocol and topology, for example, a demand of particular VPI and VCI, you should adjust accordingly the default settings to be able to adapt to the changes. • 3.4.1 Checking for Proxy Service If the browser software on the computer is configured to use a proxy server for Internet access, it is necessary to first disable the proxy connection. In Windows Internet Explorer, you can check whether a proxy server is enabled using the following procedures: Explorer Window. • Figure 3-2 Enter user name and password Use the default user name: admin and password: admin for first time setup. You can change the password once you have opened the Web-based configuration manager. The user name and password allows any computer on the same subnet as the MT800 to access the Web-based configuration manger.

It is recommended that you assign rule IDs in multiples of 5 or 10 (e.g., 10, 20, 30) so that you leave enough room between them for inserting a new rule if necessary. • occurring in the previous x minutes. (Logging may be helpful when troubleshooting.) This information can also be e-mailed to administrators. Security Level: The security level that must be enabled globally for this rule to take affect. A rule will be active only if its security level is the same as the globally configured setting (shown on the main IP Filter page). • gt: any source IP address that is numerically greater than the specified address.

Otherwise, the configuration in the flash could be damaged. 4.21 Alarm Figure 4-44 Alarm You can view the logs of alarm in response to system events. Select Refresh rate from the drop-down menu. Click the Save Alarm button to save the log file to local disk.

This button resets the device settings to the manufacturer’s default values. Any custom settings will be lost. 4.20 Firmware Upgrade Click the hyperlink Firmware Upgrade in the Wizard column to open the Firmware Upgrade page and update the system software. • Caution: Do not power off the MT800 during the firmware upgrade process. Otherwise, the configuration in the flash could be damaged. 4.21 Alarm Figure 4-44 Alarm You can view the logs of alarm in response to system events. Select Refresh rate from the drop-down menu.

• SmartAX MT880a ADSL CPE User Guide HUAWEI TECHNOLOGIES CO., LTD. • SmartAX MT880a ADSL CPE V100R001 User Guide Issue Date 2009-01-04 Part Number 103123. Corel products keygen 2018 download. • Copyright © Huawei Technologies Co., Ltd. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.

LAN IP Address: Type in the IP address for the Ethernet LAN interface. The default IP address is 192.168.1.1 LAN Network Mask: Type in the Subnet Mask for the Ethernet LAN IP interface. Save Click the Submit button to save the settings in the RAM. To save these configuration changes permanently, enter the Save & Reboot page, select Save and click Submit button to save new settings. Note: If you change the IP address, you need login in again. 4.6 DHCP Mode Configuration Click the DHCP Mode of Other Setting in the Wizard Column to set the DHCP mode. • DHCP Server MT800 can be configured as DHCP server of LAN.

Encapsulation Usually you can keep the default value: LLC. • 5.4 RFC 2684 Bridged (Pure Bridge) Configuration Configurations on MT800 Location Parameters Comments Select any one from the eight PVCs. VPI/VCI The value shall be provided by your ISP.

16 4.3.2 RFC2684 Route (IPoA) Configuration. 23 4.3.3 PPP Configuration. 24 4.4 ADSL Mode Configuration.30 4.5 LAN Configuration. 31 4.6 DHCP Mode Configuration.33 4.7 DNS Configuration. • 4.20 Firmware Upgrade.77 4.21 Alarm. 78 Chapter 5 Service Configuration. 79 5.1 Preparation for Service Configuration.

Huawei Wifi Modem

Default Route: This setting specified the IP address below is used for default route of LAN. The data will be sent through WAN interface whenever a client LAN computer accesses the Internet. • Configured MTU: Enter the maximum bytes of the packet being transmitted during connection.

• Table 3-2 Configuration for the pure bridge mode Name Configuration PVC Mode Pure Bridge PVC Operation Mode Enable VPI/VCI Provided by the ISP Encapsulation Provided by the ISP Install the PPP dial-up software to your computer to access the Internet (The PPP dial-up software Windows XP operation system is provided with the PPP dial-up software) • Select Pure Bridge in the PVC change page. Set the operation mode to Enable. Configure relevant parameters in Figure 3-2 according to the values in the Table 3-2. Figure 3-2 Configuring the pure bridge mode Click Submit. Select Tools > Save & Reboot in the navigation tree. Select Save in the Save/Reboot page.

If the LAN indicator is still off, contact an authorized maintenance center. • Settings dialog box, ensure that Use a proxy server for your LAN (These settings will not apply to dial-up or VPN connections). Check box is not selected. Step 8 Try to access multiple other Web sites to check whether the terminal can access. • Therefore, use this function with caution. ADSL It is used to connect to the MODEM interface on the splitter. It is the power button on top of the MT880a and is used to power on or power off the MT880a.

(42.17 MB) Pierce The Veil Collide With The Sky (1.85 MB) Pierce The Sky Hina mix Source title: Pure Graphics 5 - The Guestbook =) Ad (77.87 MB) 5th A Moon Child in the Sky ( album) (61.92 MB) ayaka Sing to the Sky ( album) [2008 06 26] Source title: sports.show. Amazarashi sing to the sky.

16 4.3.2 RFC2684 Route (IPoA) Configuration. 23 4.3.3 PPP Configuration. 24 4.4 ADSL Mode Configuration.30 4.5 LAN Configuration. 31 4.6 DHCP Mode Configuration.33 4.7 DNS Configuration.

• Caution: Do not reboot the device using the Reset button on the back panel of the MT800 to activate new changes. This button resets the device settings to the manufacturer’s default values.

Configure any of the following settings that display in the Firewall Global Configuration table: Blacklist Status: If you want the device to maintain and use a black list, click Enable. Click Disable if you do not want to maintain a list. • Max Half open TCP Connection: Set the percentage of concurrent IP sessions that can be in the half-open state. In ordinary TCP communication, packets are in the half-open state only briefly as a connection is being initiated; the state changes to active when packets are being exchanged, or closed when the exchange is complete. • time that you specify. You can enable or disable use of the black list using the settings described above.

Please make sure that your power adapter is in conformity with the sign in the rear panel (9V AC 1A or 9V DC 1A). Waterproof should be used during the storage, transportation and running of the equipment. • Chapter 8 Appendix 8.1 Factory Default Settings User name admin Password admin IP address 192.168.1.1 Subnet mask 255.255.255.0 DSL Mode Multimode PVC0 VPI =0 VCI=35 PVC1 VPI =8 VCI=35 PVC2 VPI= 0 VCI= 100 RFC 2684 Bridged PVC3 VPI =0 VCI=32 Mode PVC4. • Abbreviation Description Asynchronous Transfer Mode Customer Premises Equipment DHCP Dynamic Host Configuration Protocol Domain Name Server DSLAM Digital Subscriber Line Access Multiplex HTML Hypertext Markup Language Internet Protocols ICMP Internet Control Message Protocol IPoA Internet Protocols Over ATM Internet Service Provider Local Area Network Media Access Control Management Information Base. • Abbreviation Description Transfer Control Protocol TFTP Trivial File Transfer Protocol User Datagram Protocol Virtual Channel Identifier Virtual Path Identifier Wide Area Network. • Huawei Technologies Co., Ltd.

Huawei Drivers Download

• Open your browser and visit • You should be prompted with a login dialogue. • Enter the username: admin and the password admin Note: If you have already changed the password use that instead. • You will now be logged in. If you haven't yet changed the defaul password, we recommend that you change it first thing you do after logging in. If these instructions don't work for your router, you can always try a factory reset to get the default, or try some other common, as they can usually be shared across models/variants.